This multifunction analyzer takes advantage of digital signal processing techniques to perform both transmission and signal quality tests, on both analog and digital signals. See options below.
When installed in and 860 DSP this option enables signal generation for the Return Sweep Recevier Option (SR-1), Return Tester RSVP Option (VP-1), and/or Frequency Domain Reflectometer Option (FDR). REQUIRES POWER PACK OPTION. For aftermarket purchases of this option, you must also purchase the SR-1, VP-1, and/or FDR Option.
When installed in an 860 DSP, this option performs functions of the Trilithic Guardian 9580 SSR Reverse Test Field Unit. Compatible with the Guardian and Guardian II System. REQUIRES RETURN TRANSMITTER BOARD OPTION. This option or the Return Tester RSVP Option (VP-1) is required to enable the Real-Time Transport Protocol Reflector Option (RTP-1).
When installed in an 860 DSP, this option performs functions of the RSVP². Test capabilities and displays allow RSVP² type testing of 8 frequencies at one time. Compatible with the Guardian and Guardian II System. REQUIRES RETURN TRANSMITTER BOARD OPTION. This option or the Return Sweep Receiver Option (SR-1) is required to enable the Real-Time Transport Protocol Reflector Option (RTP-1).
When installed in an 860 DSP, this option harnesses the power of the 860 DSP to provide all of the typical and high performance spectrum analyzer capabilities without the complexity, cost and weight of analog alternatives.
With this option the 860 DSP analyzes QPSK and all common QAM formats from 4 QAM to 256 QAM, including deep interleave on 256 QAM, presenting constellation diagrams, MER, EVM and calculated BER, both pre and post FEC.
When installed in an 860 DSP, this option provides compatibility with the 8300 FST Forward SpeedSweep Transmitter.
When installed in an 860 DSP, this option allows the operator to connect an off air antenna to the 860 DSP input port and read Level, MER, BER, and view Constellation and Equalizer Tap Information on 8 VSB and 16 VSB channels. REQUIRES FIRMWARE VERSION V7.4.1.1 or HIGHER. Aftermarket purchases require the Enhanced Digital Video Retrofit (IL-2). REQUIRES POWER PACK OPTION.
When installed in an 860 DSP, this option allows headend technicians to view Vertical Interval Test Signals (VITS), which are inserted during the vertical synchronization interval of analog video, and specify lines for testing. The option enables the technician to measure differential phase, differential gain, and chroma delay.
When installed in an 860 DSP, this Option provides a way to troubleshoot upstream ingress and noise problems within active channel bands by seeing the ingress that is present “underneath” an upstream cable modem channel, or any bursty signal.
When installed in an 860 DSP, this option extends the measurement and troubleshooting range of field technicians by offering a simple round-trip VoIP quality test from any RF test point. The option works through communication with the Tektronix DirectQuality active monitoring system, enabling tests to verify RTP communication from the test point to probes placed strategically throughout the cable network. The RTP Reflector Option enables round-trip stream analysis for packet loss, jitter, delay and other IP impairments. R-factor, MOS and other industry-standard service quality metrics are included based on a Tektronix E-model implementation.This option works only with a fully implemented Tektronix DirectQuality System. REQUIRES FIRMWARE VERSION V8.1.11.1 or HIGHER.
When installed in an 860 DSP, the Frequency Domain Reflectometer Option (FDR) provides a simple, convenient and accurate tool for determining the distance to cable faults. The option works by sending a sweep into the cable and analyzing the complex reflected wave to determine the distance to various sources of reflection (opens, shorts, splitters, etc.). The reflecting events are indicated on a distance versus amplitude display, and markers are used to identify the distance to the source of the reflection, and the return loss at that point. REQUIRES RETURN TRANSMITTER BOARD OPTION.
Bi-directional test probe used with the Return Sweep Receiver Option (SR-1) for the 860 DSP & DSPi or the 9580 SSR to isolate ingress sources.
Return measurement lowpass filter.
Carrying case designed to house an 860 DSPi, Seeker, Seeker Lite or Seeker Lite², power adapter/charger, test cables, probes and more. Includes Precision RF Coaxial Test Cable (I/O-15).
Vehicle cigarette adaptor for the 860 DSP & 860 DSPi.
Euro AC power cable for Trilithic products. This is a Euro standard 2.5 Meter power cable with a Continental Europe 2-prong plug Male (IEC 884/CEE 7/VII) to 3-pin shroud plug Female (IEC 320C13).
Can be used to replace the Euro power cable that is included with the following products:
Can be used as an accessory for the following products:
Data cable for the 860 DSP & DSPi. This data cable is used to connect to a PC using the WorkBench software.
Precision RF coaxial test cable for connecting test equipment. Light, very flexible with a tight bend radius. 0.16” dia, 4’ Long, ~ 0.7 db loss at 1 GHz. Lab-quality Male F-connector on both ends, Includes one (1) F Style Push On Adaptor.
Lab-quality adaptor for precision measurements. Female F-connector to Male push on F-connector. Loss ~ 0.1 dB at 1 GHz.
Replacement input F-connectors for the 860 DSP & 860 DSPi. Minimum quantity of purchase is 25 pieces.
For use with 860 DSP & 860 DSPi.
AC to DC power adaptor & battery charger for Trilithic Products. This is a standard AC to DC power supply (90 - 220 VAC) with a U.S. standard 6 Foot power cable with a 3-prong grounded plug Male (NEMA 5-15P) to 3-pin shroud plug Female (IEC 320C13).
Can be used to replace the AC to DC adaptor & battery charger that is included with the following products:
AC power cable for Trilithic products. This is a U.S. standard 6 Foot power cable with a 3-prong grounded plug Male (NEMA 5-15P) to 3-pin shroud plug Female (IEC 320C13).
Can be used to replace the US power cable that is included with the following products:
Replacement Ni-MH battery for the 860 DSP & 860 DSPi.
Cloth carrying case for the 860 DSP.
Shoulder strap for 860 DSP & 860 DSPi.
Set of five (5) clear plastic adhesive shields used to protect the display of the 860 DSP & 860 DSPi.
Server application enables a proprietary connection with the 860 DSP, 860 DSPi, and 860 DSPr analyzers for communication and testing Packet Loss, Latency, Jitter and MOS of VoIP services using the 860 DSP, 860 DSPi, and 860 DSPr. Includes separate pass/fail results for forward and return path troubleshooting. In addition to the VoIP tests, this software enables high speed throughput tests using the 860 DSPi with speeds up to 40 Mbps, and can also be used as a ping test reflector. Located as close as possible to the PSTN gateway to ensure optimal testing that includes only the cable network. Runs on minimal hardware configuration (service is time sensitive, so it takes priority over other applications). REQUIRES ETHERNET UPGRADE KIT (CI-4) PLUS an EXTERNAL CABLE MODEM for the 860 DSP.
Free Configuration Starter Software for the 860 DSP, 860 DSPi, 860 DSPh, and 860 DSPr analyzers and 8300 FST Forward SpeedSweep Transmitter. This software is used to facilitate custom configurations including Channel Plans, Auto Tests, and Firmware Updates via the meter’s Ethernet port. Requires Windows® 2000 or higher operating system.
This WorkBench Lite software also includes a 30-day evaluation period for the advanced datalog analysis features of WorkBench. After 30 days elapse without a registration code being entered, the advanced datalog analysis feature will be de-activated. To unlock the advanced datalog analysis features aftter the 30-day evaluation period, you will need to obtain a license for the premium version of the WorkBench software. A license can be purchased and activated by phone, contact Trilithic Sales for more information.
Software for the 860 DSP, 860 DSPi, 860 DSPh, and 860 DSPr analyzers and 8300 FST Forward SpeedSweep Transmitter. Create configuration packages for Channel Plans and Auto Tests. Perform Firmware updates, retrieve, display, graph, or export technical data via the meter’s Ethernet port, or serially with the included Data Cable (I/O-14). Requires Windows® 2000 or higher operating system.
For current users of WorkBench Software. Activates TDM Component within WorkBench software for up/down loading channel plans, auto-tests, firmware updates and technical data to the TDM server. REQUIRES WORKBENCH SOFTWARE VERSION 2.0 or HIGHER.
Includes WorkBench Software with TDM component for uploading/downloading information to TDM server.
Pre-configured server, integrating powerful software and hardware to provide remote access to channel plans, auto test, and firmware updates, supports data uploads via the Internet. Measurement data and work order management tracking and report features are compatible with major WFM systems. The server hardware comes pre-configured with 6 WorkBench/TDM Software Packs. TDM Server can store more than 10 million data logs (average data log is 34 kB).
This is a rack-mounted U.S. 6 MHz unit that generates forward sweep transmissions that step around system carriers to avoid interference, filling in vacant spectrum areas for a complete view of network frequency response.
This is a rack-mounted Euro 8 MHz unit that generates forward sweep transmissions that step around system carriers to avoid interference, filling in vacant spectrum areas for a complete view of network frequency response.
The 8310 RSA™ Return SpeedSweep Analyzer rack mounted unit receives a sweep initiated from a field test point by an 860 DSPi™ Field Analyzer and transmits the received sweep level information back to the 860 DSPi™ on a downstream telemetry signal. The complete kit includes the 8310 RSA™ rack mounted (2U) unit, AC Power Cable, and Operation Manual on CD.
Currently, the following products are in your quote:
